Constructed from stainless steel, the Migali C-DD72-3-HC Direct Draw Beer Cooler has a corrosion resistant exterior made to survive daily wear-and-tear. Its exterior dimensions are 72.8 inches wide, 24.4 inches deep, 35.875 inches high. Its 423 pounds of weight rests evenly on 4 levelling feet.
The Top of the Migali C-DD72-3-HC Direct Draw Beer Cooler is made from stainless steel as well. On it are 2 single heads that connect to the inSide. It has three doors each with their own recessed handles. The recessed handles help this equipment take up less space and create more room for working in front of it.
Made of stainless steel, the interior measures 60 inches in width, 20.13 inches in depth, and 31 inches in height. Its 19.6 cubic feet capacity can hold three ½ barrel kegs. A Side mounted, 1/3 horsepower compressor helps contents stay chilled. Its forced air refrigeration system uses a natural R290 Hydrocarbon Refrigerant to produce cooling. Dedicated air tubes ensure that all its cold is directed towards the content themselves.
A digital controller equipped with a read-out will help you regulate the temperature of the Migali C-DD72-3-HC Direct Draw Beer Cooler. It, along with the compressor, uses 115 volts-1 phase-60 hertz and 7.4 amps. This is obtained using a Nema 5-15P plug.
LongDescription#@#NA#@@#Cleaning Instructions#@#Unplug the equipment before cleaning. Remove its lower grill using a Phillips screwdriver. Remove the compressor assembly, unbolting it to allow it to be extracted. Clean the condenser coil and fan blades using a stiff bristle brush. Then, vacuum the interior floor. Secure everything back in place before plugging the equipment in again. Do this to check whether to condenser is working.
For the stainless steel, follow its polish lines to prevent scratches from improper wiping. It is recommended to use a non-chloride cleaner in order to avoid corrosion. It is also preferable if you use soft water as that reduces the rate at which deposits accumulate. Clean the surfaces regularly to prevent hard stains from forming.#@@#Additional Info#@#The Migali C-DD72-3-HC Direct Draw Beer Cooler is c-ETL-us and ETL sanitation listed. It is certified by ISO and US Department of Energy.#@@#General Info#@#Constructed from stainless steel, the Migali C-DD72-3-HC Direct Draw Beer Cooler has a corrosion resistant exterior made to survive daily wear-and-tear. Its exterior dimensions are 72.8 inches wide, 24.4 inches deep, 35.875 inches high. Its 423 pounds of weight rests evenly on 4 levelling feet.
The Top of the Migali C-DD72-3-HC Direct Draw Beer Cooler is made from stainless steel as well. On it are 2 single heads that connect to the inSide. It has three doors each with their own recessed handles. The recessed handles help this equipment take up less space and create more room for working in front of it.
Made of stainless steel, the interior measures 60 inches in width, 20.13 inches in depth, and 31 inches in height. Its 19.6 cubic feet capacity can hold three ½ barrel kegs. A Side mounted, 1/3 horsepower compressor helps contents stay chilled. Its forced air refrigeration system uses a natural R290 Hydrocarbon Refrigerant to produce cooling. Dedicated air tubes ensure that all its cold is directed towards the content themselves.
A digital controller equipped with a read-out will help you regulate the temperature of the Migali C-DD72-3-HC Direct Draw Beer Cooler. It, along with the compressor, uses 115 volts-1 phase-60 hertz and 7.4 amps. This is obtained using a Nema 5-15P plug.#@@#Delivery Details#@#• Two or more persons are recommended for handling of this equipment.
• If you do not have an available loading dock, use a lift gate instead.
• Keep the equipment upright. Mishandling of the equipment may damage it.
• Once received, thoroughly inspect the equipment for any damage obtained in shipping.
• Do not install this equipment in areas exposed to direct sunlight, rain, or heat.
• Verify whether your electrical supply and the equipment’s specifications match.
• Do not attempt to operate this equipment using an adapter plug and/or extension cord.
• Storage and use of flammable, corrosive, or explosive materials and compounds must not be conducted in the vicinity of this equipment.
• Consult the equipment’s manual before undertaking any installation or operation.#@@#deliverynotes#@#Culinary Depot usually ships the Migali C-DD72-3-HC Direct Draw Beer Cooler within # business days after receiving cleared payment.#@@#Maintenance Guide#@#Once every month, clean the condenser of the Migali C-DD72-3-HC Direct Draw Beer Cooler. This is to prevent failure of the compressor. Make sure that the condenser is see-through before deeming it clean. Its condensing coil should never be obstructed as that prevents the steady flow of air into the coil. Use of corrosive chemicals or abrasive cleaning tools may damage the stainless steel and is therefore discouraged.