The Migali C-DD60-2-HC Direct Draw Beer Cooler has a crisp, modern exterior constructed from black stainless steel. It has external dimensions of 60.8 inches wide, 24.4 inches deep, and 35.875 inches high. Its weight of 394 pounds rests on 4 leveling feet.
The Top is made from stainless steel and has 2 single heads attached to it. Beneath that are two doors with recessed handles for a minimalist touch. Opening it leads into a stainless steel interior measuring 48 inches wide, 20.13 inches deep, and 31 inches high. The Migali C-DD60-2-HC Direct Draw Beer Cooler has a capacity of 15.8 cubic feet and is able to hold 2 ½ kegs. Air tubes run along the interior to keep the contents perfectly chilled.
Its refrigeration system forces cold air equally throughout the interior. This is done by a Side-mounted 1/3 horsepower compressor using a R290 Hydrocarbon Refrigerant. Its temperature, displayed on a digital read-out, can be fine-tuned using a digital temperature controller. The Migali C-DD60-2-HC Direct Draw Beer Cooler does this using 115 volts-1 phase-60 hertz and 6.4 amps facilitated through a Nema 5-15P plug.
LongDescription#@#NA#@@#Cleaning Instructions#@#To clean the condenser, disconnect the equipment from its power source. Use a Phillips screwdriver to remove the lower grill. The compressor assembly must first be unbolted before removal. Use a stiff bristle brush to clean dust from the condenser coil. The fan blades are to be cleaned similarly. Vacuum the interior floor before reinstalling all the components. Make sure everything is secured in place. Lastly, plug it in to check if the condenser is working.
Clean the stainless steel surfaces, following the polish lines to avoid scratching it. Use a non-chloride cleaner to avoid corrosion. Soft water is preferred for cleaning as this reduces deposits from accumulating. To prevent hard stains, clean it regularly.#@@#Additional Info#@#The Migali C-DD60-2-HC Direct Draw Beer Cooler is listed by c-ETL-us and ETL sanitation and certified by ISO and US Department of Energy.#@@#General Info#@#The Migali C-DD60-2-HC Direct Draw Beer Cooler has a crisp, modern exterior constructed from black stainless steel. It has external dimensions of 60.8 inches wide, 24.4 inches deep, and 35.875 inches high. Its weight of 394 pounds rests on 4 leveling feet.
The Top is made from stainless steel and has 2 single heads attached to it. Beneath that are two doors with recessed handles for a minimalist touch. Opening it leads into a stainless steel interior measuring 48 inches wide, 20.13 inches deep, and 31 inches high. The Migali C-DD60-2-HC Direct Draw Beer Cooler has a capacity of 15.8 cubic feet and is able to hold 2 ½ kegs. Air tubes run along the interior to keep the contents perfectly chilled.
Its refrigeration system forces cold air equally throughout the interior. This is done by a Side-mounted 1/3 horsepower compressor using a R290 Hydrocarbon Refrigerant. Its temperature, displayed on a digital read-out, can be fine-tuned using a digital temperature controller. The Migali C-DD60-2-HC Direct Draw Beer Cooler does this using 115 volts-1 phase-60 hertz and 6.4 amps facilitated through a Nema 5-15P plug.#@@#Delivery Details#@#• Two or more persons are recommended for handling of this equipment.
• A lift gate will suffice should a loading dock be unavailable.
• Keep the equipment upright as mishandling may damage it.
• Once received, check the equipment for damage it may have received during the delivery process.
• This equipment should not be installed in an area exposed to heat or direct sunlight.
• Make sure that the equipment and your power supply match.
• Never use an extension cord to operate this equipment.
• Do not use this equipment with an adapter plug.
• Storage of flammable, corrosive, or explosive materials and compounds should not be done in the vicinity of this equipment.
• Do not install nor operate this equipment without first referring to its manual.#@@#deliverynotes#@#Culinary Depot usually ships the Migali C-DD60-2-HC Direct Draw Beer Cooler within # business days after receiving cleared payment.#@@#Maintenance Guide#@#The condenser should be cleaned regularly every 30 days to prevent compressor failure. To be deemed sufficiently clean, you should be able to see through the condenser. The condensing coil should not be obstructed by any means as it blocks air from flowing into the coil. Do not use abrasive or corrosive cleaning tools and/or chemicals as those may damage the stainless steel.